用途：鹽水噴霧試驗箱是對各種材質表面處理，包含涂料、電鍍、有機及無機皮膜、陽 處理、防銹處理等耐蝕之品質進行測試。

      1、檢查電源（電源220V ）是否插好，供水、供氣裝置[外接8"氣管到機器后面]是否正常連接并處于打開狀態，排水閥是否處于關閉狀態，排氣裝置是否連接到室外或下水管道上；安裝在窗口邊：有利于排水、排氣。機器放置位置后面離墻有10cm,兩側則留維護之空間。排水管可用PVC1/2"硬管排放，須注意水管應低于排水口。排氣管需用硬管PVC21/2“硬管，沿伸至室外排放，須注意排氣管之安裝，可由機器平行向下。

      2、試驗室加水：

    （3）如果供水裝置已經正常連接，打開供水閥，按下“電源"鍵，設備將自動往試驗室加水，直至操作面板的“低水位"燈滅（該“低水位"燈對應試驗室水位）。

    （2）如果未連接供水裝置，按下“電源"鍵后手工往試驗室里倒入自來水，直到試驗室“低水位"燈滅掉。

      3、壓力桶加水：

      如果供水裝置已經正常連接，并且供水閥處于打開狀態，按下“電源"鍵后，設備將自動往壓力桶加水（加入壓力桶的水會經過一道過濾），直至操作面板的“低水位"燈滅（該“低水位"燈對應壓力桶水位）。在實驗過程中使設備一直處于供水狀態，以免因壓力桶缺水而導致實驗暫停； 注：*次使用鹽霧試驗箱或者將壓力桶水清空后再次注水，需在低水位燈滅掉之后再通過“壓力桶手動加水處"往里加入純凈水！